2017-2023 | Model 3 Front Lip Splitter Gen. 2 (3 Piece Style) - Real Molded Carbon Fiber
2017-2023 | Model 3 Front Lip Splitter Gen. 2 (3 Piece Style) - Real Molded Carbon Fiber
2017-2023 | Model 3 Front Lip Splitter Gen. 2 (3 Piece Style) - Real Molded Carbon Fiber
2017-2023 | Model 3 Front Lip Splitter Gen. 2 (3 Piece Style) - Real Molded Carbon Fiber
2017-2023 | Model 3 Front Lip Splitter Gen. 2 (3 Piece Style) - Real Molded Carbon Fiber
2017-2023 | Model 3 Front Lip Splitter Gen. 2 (3 Piece Style) - Real Molded Carbon Fiber
2017-2023 | Model 3 Front Lip Splitter Gen. 2 (3 Piece Style) - Real Molded Carbon Fiber
2017-2023 | Model 3 Front Lip Splitter Gen. 2 (3 Piece Style) - Real Molded Carbon Fiber
2017-2023 | Model 3 Front Lip Splitter Gen. 2 (3 Piece Style) - Real Molded Carbon Fiber
2017-2023 | Model 3 Front Lip Splitter Gen. 2 (3 Piece Style) - Real Molded Carbon Fiber
2017-2023 | Model 3 Front Lip Splitter Gen. 2 (3 Piece Style) - Real Molded Carbon Fiber
2017-2023 | Model 3 Front Lip Splitter Gen. 2 (3 Piece Style) - Real Molded Carbon Fiber
2017-2023 | Model 3 Front Lip Splitter Gen. 2 (3 Piece Style) - Real Molded Carbon Fiber
2017-2023 | Model 3 Front Lip Splitter Gen. 2 (3 Piece Style) - Real Molded Carbon Fiber
2017-2023 | Model 3 Front Lip Splitter Gen. 2 (3 Piece Style) - Real Molded Carbon Fiber
2017-2023 | Model 3 Front Lip Splitter Gen. 2 (3 Piece Style) - Real Molded Carbon Fiber
2017-2023 | Model 3 Front Lip Splitter Gen. 2 (3 Piece Style) - Real Molded Carbon Fiber

2017-2023 | Model 3 Front Lip Splitter Gen. 2 (3 Piece Style) - Real Molded Carbon Fiber

$598.75 Sale • Save
$419 - $480 with 30% on orders over $100

Finish Glossy (Wet Look)


Item is in stock Only 0 left in stock Item is out of stock Item is unavailable

Adding to Cart Added to Cart

This front lip is made out of real molded carbon fiber, very easy to install and the cost of shipping is more affordable than most 1 piece front lips. The full wrap around look is achieved by the right and left hand pieces that cover both ends of the front lip where it ends inside of the front fender liner.

It encourages airflow to pass under the center of the front lip as well as on the sides of the vehicle, improving traction and helps the car to hug the road tighter, increasing stability at high speeds and around turns. It also protects the bumper of the car from any damage and gives the Tesla a lower, cleaner look. 

All of our Carbon Fiber Spoilers are made from Genuine Molded Carbon Fiber which is woven carbon fiber without fillers.  They are UV and coated Ceramic Pro 9H coated which helps prevent yellowing or fading.

Finish Choices:  The glossy version is rich and very striking, it has a wet look which features a deep 3D lustrous appearance.  Matte is flat, is dry looking, and does not have the same deep 3D look.

Ground Clearance:  The front end ground clearance is only 1/2" lower than your stock bumper. If you have lowering springs or coilovers this will not scratch on curbs or speed bumps. Caution is needed when parking close up to taller parking blocks, but this 1/2" will not affect your normal parking or driving. 

Installation:  The 2 end pieces are installed with double sided tape and they attach with the stock OEM grommets located under the bumper.  Just pop the 3 grommets off, install the 2 end pieces and replace the grommets in both sides.  The center piece attaches with 4 self tapping screws, we supply, or with rivets.

Our installation video is below.  Please watch it to understand the full installation. 

Carbon Pattern Warranty: Real Molded Carbon Fiber is hand laid and is not Prepreg Wet Molded, so it may show imperfections in pattern direction. These variations are normal and are not a manufacturer's defect. Please refer to our Return Policy if you would like to return them.

UV Warranty: Our Real Molded Carbon Fiber is coated with 3 coats of UV Protection. Over time without proper care from waxing or applying a nano-ceramic coating, this protection can wear off. The warranty is limited to 1 year. Slight yellowing is normal for carbon fiber when parked outside in direct sunlight and is not covered under our warranty. To extend the life of our Carbon Fiber, we recommend using "303 Protectant”. Ceramic coatings will assist with UV protection and we recommend Ceramic Pro. Lastly, after you install it we recommend wrapping it in clear bra paint protection film. This will only work on the glossy finish, and will prevent pitting, scratching and denting over time.

NOTE: These are considered USED as soon as the double sided adhesive liner is removed. Used items are NOT RETURNABLE so please be sure you're happy with the way it looks and place it on your TESLA before removing the adhesive liner.

No screws, no drilling, only double sided tape is used to install this front lip. Simply clean the lower front bumper, then spray on the soapy water solution that we supply, and slide the front lip on. It dries and holds.

Our installation videos provide the necessary information to correctly install our products. Therefore, we strongly recommend that you watch the installation video/s both before ordering and before installing our products.

Shipping information: Medium

If you are in Southern California, and want to pickup your order, we are located at 23201 Antonio Parkway, Rancho Santa Margarita CA 92688, please select "Pickup" at checkout.

Variable Shipping Cost Note: When purchasing multiple oversize products, shipping cost will be calculated for each oversized product individually.

NOTE* To see if your order qualifies for lower cost shipping method, please email us with your shipping address prior to purchasing.

INTERNATIONAL ORDERS: International Customers are responsible for all import fees, duties, VAT, GST, TAX, handling fees, and all other import costs in their country. The shipping fees RPM collects only covers shipping & handling.

Australia

$250

Canada

$140

California

$60

USA - Contiguous

$60

USA - Non Contiguous

$200

Rest of World

$300

You might also like